Fanless and Silent
Passive cooling, no fan noise at all
Perfect to be used in noise-sensitive environments
Fanless, dust-free and thus virtually maintenance-free
Low Power Consumption
Power consumption in idle mode under Windows 10: ca. 7~8 W only
24/7 Nonstop Operation
This device is approved for 24/7 permanent operation.
- Free circulation of air amongst the PC must be guaranteed.
- Ventilation holes must stay clear.
- If a hard disk is installed, this must also be approved for permanent operation by its manufacturer
Slim-PC (Nettop) with black chassis made of steel
Without cooling fan, passive cooling only
The bays for memory, 2.5" drive and M.2 card
can be easily accessed by removing two cover plates.
Dimensions: 200 x 165 x 39.5 mm (LWH) = 1.3 litres
Weight: 1.43 kg net and 2.13 kg gross
Two holes for Kensington Lock and numerous
threaded holes (M3) at both sides of the chassis
1) Vertical: Usually operated in vertical position with the supplied feet (DisplayPort output facing up).
2) VESA-mounted: The device can also be mounted behind an appropriate monitor using the supplied VESA mount kit.
Note: From a thermal point of view horizontal operation is permitted, however, there are no rubber feet on the device. The maximum operating temperature is 35 °C then.
This barebone system comes without operating system.
It is compatible with Windows 10 (64- bit) and Linux (64- bit).
Model: Intel Core i7-7500U (ULV)
System-on-a-chip architecture (SoC): no chipset required
BGA1356 package - directly soldered onto the mainboard
Code name: Kaby Lake-U (7th Generation Intel Core)
Cores / Threads: 2 / 4
Clock rate: 2.7~3.5 GHz
L1/L2/L3 Cache: 128 kB / 512 kB / 4096 kB
Memory controller: DDR4-2133 Dual Channel (1.2 V)
TDP wattage: 15 W maximum
Manufacturing process: 14 nm
Maximum Tjunction Temperature: 100 °C
Supports Hyper-Threading (HT), 64-bit, VT-x (EPT), VT-d, Enhanced SpeedStep, NX bit, AES-NI, SSE 4.1/4.2
Integrated graphics engine
Intel HD graphics 620
GPU clock frequency: 300~1050 MHz
Execution Units (EUs): 24
Three digital audio/video ports support three independent screens:
Supports Ultra HD / 4K resolution at 3840 x 2160 Pixels
1) DisplayPort 1.2  supports Ultra HD @ 60 Hz
2) 2x HDMI 1.4b supports Ultra HD @ 30 Hz
Note: the DisplayPort of DS77U7 does not support audio output
Mainboard / BIOS
Shuttle Mainboard FS77
All capacitors are high quality solid capacitors
Supports resume after power failure 
Supports Wake on LAN (WOL)
Supports Power on by RTC Alarm
Supports boot from M.2 SSD cards, USB devices and SD card reader
AMI BIOS in 8 MByte EEPROM with SPI interface
Supports hardware monitoring and watch dog function
Supports Unified Extensible Firmware Interface (UEFI)
Supports Firmware-TPM (fTPM) Version 2.0
External 65 W power adapter (fanless)
Input: 100~240 V AC, 50/60 Hz, max. 1.6 A
Output: 19 V DC, max. 3.42 A, max. 65 W
DC Input connector
DC Input Connector: 5.5 / 2.5 mm (outer/inner diameter)
The DC-input of the computer supports an external
power source with either 12V±5% or 19V±5%.
2x SO-DIMM slots with 260 pins
Supports DDR4-2133 (PC4-17000) SDRAM at 1.2 V
Supports Dual Channel mode
Supports a maximum of 16 GB per DIMM,
maximum total size: 32 GB
Supports two unbuffered DIMM modules (no ECC or registered)
2.5" Drive Bay with SATA connector
Supports one Serial ATA hard disk
or one SATA SSD drive in 6.35 cm / 2.5" format
Device height: max. 12.5 mm
Supports Serial-ATA III, 6 Gb/s (600 MB/s) bandwidth
Supports Unified Extensible Firmware Interface (UEFI)
Note: no Serial ATA cable is required
M.2 Slot for SSDs
The M.2 2280 BM slot provides the following interfaces:
- PCI-Express Gen. 3.0 X4 with up to 32 Gbps Data Transfer Speed
- SATA v3.0 (max. 6 Gbps)
It supports M.2 cards with a width of 22 mm
and a length of 42, 60 or 80 mm (type 2242, 2260, 2280).
Supports M.2 SATA SSDs (with B+M key) and M.2 PCIe SSDs (with M key)
Integrated SD card reader
Supports SD, SDHC and SDXC memory flash cards
Supports booting from SD card
Audio Realtek® ALC 662 High-Definition Audio
Two analog audio connectors (3.5 mm) at the back panel:
1) 2 channel line out (headphones)
2) microphone input
Digital multi-channel audio output: via HDMI
Dual Gigabit LAN
Dual network with two RJ45 ports
Used network chips:
1) Intel i211 Ethernet Controller with MAC, PHY and PCIe interface
2) Intel i219LM PHY connected to the MAC of the processor
Supports 10 / 100 / 1.000 MBit/s operation
Supports WAKE ON LAN (WOL)
Supports network boot by Preboot eXecution Environment (PXE)
Supports Teaming mode 
Wireless Network (WLAN)
Built-in M.2-2230-A/E WLAN card and internal antenna
Single-Chip 1T1R WLAN Controller Realtek RTL8188EE
Supports IEEE 802.11b/g/n, max. 150 Mbps up-/downstream
Security: WPA/WPA2(-PSK), WEP 64/128 bit, IEEE 802.11x/i
Front Panel connectors
2x USB 3.0
2x USB 2.0
2x RS232 serial ports (5V / 12V, 1x switchable to RS422 / RS485) 
covered with black plastic caps
SD card reader (supports SD, SDHC, SDXC)
Power LED (blue)
HDD LED (yellow)
Back Panel connectors
DisplayPort 1.2 
2x HDMI 1.4b
2x USB 2.0
2x Intel Gigabit LAN (RJ45)
Audio Line-out (headphones)
DC-input connector for external power adapter
4-pin connector "SW2" (2.54 mm pitch) for power button, Clear CMOS and 5 V DC 
By removing Jumper J9 (please refer to the quick user guide)
the system will start unconditionally once power is applied. 
Scope of Delivery
Multi-language user guide
Two metal feet with four screws M3 x 7
VESA mount for 75/100mm standard (two metal brackets)
Four thumbscrews M3 x 5 mm (screws together VESA mount and PC)
Four screws M4 x 10 mm (to fix the VESA mount to the external surface)
Rack (to mount a 2.5" storage in the bay) with two screws M3 x 4 mm
Driver DVD for Windows 10 (64-bit)
External power adapter with power cord
- CXP01: adapter cable for external power button
- PRM01: 2U rack mount front plate for two Shuttle XPC slim PCs
Operating temperature range: 0~40 °C 
Relative humidity, non-condensing: 10~90 %
Conformity & Certifications
EMI: FCC, CE, BSMI, C-Tick
Safety: ETL, CB, BSMI
Other: RoHS, Energy Star, ErP
This device is classed as a technical information equipment (ITE) in class B and is intended for use in living room and office. The CE-mark approves the conformity by the EU directives:
(1) 2004/108/EC relating to electromagnetic compatibility (EMC),
(2) 2006/95/EC relating to Electrical Equipment designed for use within certain voltage limits (LVD),
(3) 2009/125/EC relating to ecodesign requirements for energy-related products (ErP),
(4) 1999/5/EC related to Radio and Telecommunications Terminal Equipment (R&TTE)
 Jumper for COM port configuration
Pin 9 of the COM-Port is a multi-functional signal. Based on the Jumper JP1 configuration on the mainboard, it can be configured as Ring Indicator (RI) or external power supply with a voltage level of either 5 V or 12 V. Each COM port can be configured separately.
The operating mode of COM 1 can be set to RS232, RS422 or RS485 in the BIOS. COM 2 supports RS232 mode only.
 Limitations of the DisplayPort
Due to the design of the Intel chipset, the DisplayPort output of the DS77 Series is based on the Embedded DisplayPort (eDP) interface. Please be aware of the following restrictions when setting up your monitor.
1) The DisplayPort (DP) has no audio function. Please use HDMI for displays/TVs with integrated speakers.
2) Intel Collage Mode in Multi-Stream Transport (MST) mode is not available. Please use a native 4K display. Older monitors using Collage Mode are not supported.
3) PASSIVE adapters/cables cannot be used (e.g. DP-to-HDMI or DP-to-DVI). Please use a native DP connection or an ACTIVE adapter.
4) HotPlug is not supported. Please restart the system for the display to be detected.
Note: In a 3-display setup, the DP output won't show picture while booting in BIOS mode. It will be activated once the OS has loaded the display driver.
 Teaming Mode
The teaming function allows you to group both available network adapters together to function as a single adapter. The benefit of this approach is that it enables load balancing and failover.
Driver download: https://downloadcenter.intel.com/download/21642
 Four-pin header at the back panel
This header allows for connecting an external power button.
It also provides 5 V DC voltage for external devices and the Clear CMOS function. Optional accessory: the adapter cable CXP01.
 Caution: for high ambient temperatures higher than 35 °C we strongly recommend to use an SSD instead of an HDD
 Power on after power fail:
The BIOS setup provides a "Power-On after Power Fail" function that can be found under "Power Management Configuration". This function determines the PC's behaviour after power failure. As a matter of the nature of this function, it may fail after short power failures. This is why the Shuttle XPC slim Barebone DS77U7 also comes with a hardware-based solution. By removing Jumper J9 (please refer to the quick user guide) the system will start unconditionally once power is applied.